18
-EN
F/R Sub-W
3WAY
Adjusting and Storing the Crossover
Settings
Before performing the following procedures, refer to “About the
Crossover” (Page 17).
1
Press and hold
MENU
for at least 2 seconds.
2
Select the X-OVER mode by sliding your finger on
the
GlideTouch bar
to the left or right. Press the
GlideTouch bar
under the X-OVER mode.
2 WAY System
3
Press
BAND
to select the band to be adjusted.
LOW
→
MID
→
HIGH
→
LOW
4
Select the desired cut-off frequency (Crossover
Point) by sliding your finger on the
GlideTouch
bar
to the left or right.
Adjustable frequency bands: 20Hz to 200Hz
(in 1/3 octave steps)
5
Press
SOURCE/POWER
to adjust the slope.
Adjustable slope: 0 (FLAT), 1 (6dB/oct.), 2 (12dB/oct.)
3 (18dB/oct.) 4 (24dB/oct.)
6
Adjust the output level by turning the
Rotary
encoder
.
Adjustable output level: -12 to 0 dB.
7
To adjust another band, repeat steps 3 to 6, then
adjust all bands.
8
When the setting has been completed, press
FUNC.
or the
GlideTouch bar
to activate the
preset mode.
9
Select any one of the preset numbers (1 through 6)
by sliding your finger on the
GlideTouch bar
to
the left or right. Press and hold the
GlideTouch
bar
under the desire preset for at least 2 seconds
to store the adjusted contents.
10
After setting, press and hold
MENU
for at least 2
seconds to return to normal mode.
• If
MENU
is pressed while adjusting or setting the items in the
MENU mode, the unit will return to the previous selection screen.
• By pressing the
GlideTouch bar
under RETURN in the MENU
mode, the unit will return to the normal mode.
• If no operation is performed in 60 seconds, the unit will return to
the normal mode.
3 WAY System
3
Press
BAND
to select the band to be adjusted.
LOW
→
MID-L
→
MID-H
→
HIGH
→
LOW
4
Select the desired cut-off frequency (Crossover
Point) by sliding your finger on the
GlideTouch
bar
to the left or right.
Adjustable frequency bands:
LOW:
20Hz to 200Hz (in 1/3 octave steps)
MID-L:
20Hz to 200Hz (in 1/3 octave steps)
MID-H:
20Hz to 20kHz (in 1/3 octave steps)
HIGH:
1kHz to 20 kHz (in 1/3 octave steps)
5
Press
SOURCE/POWER
to adjust the slope.
Adjustable slope: 0 (FLAT)
*
1
, 1 (6dB/oct.), 2 (12dB/oct.)
3 (18dB/oct.), 4 (24dB/oct.)
*
FLAT can be set for the HIGH slope only when USER'S
is selected in “Setting the Response Slope for the High
Range Speaker (TW SETUP)” (page 28). Depending on
the response characteristics of the speaker, care should
be taken when setting the response slope to FLAT, as
speaker damage may result.
6
Adjust the output level by turning the
Rotary
encoder
.
Adjustable output level: -12 to 0 dB.
7
To adjust another band, repeat steps 3 to 6, then
adjust all bands.
8
When the setting has been completed, press
FUNC.
or the
GlideTouch bar
to activate the
preset mode.
9
Select any one of the preset numbers (1 through 6)
by sliding your finger on the
GlideTouch bar
to
the left or right. Press and hold the
GlideTouch
bar
under the desire preset for at least 2 seconds
to store the adjusted contents.
10
After setting, press and hold
MENU
for at least 2
seconds to return to normal mode.
• If
MENU
is pressed while adjusting or setting the items in the
MENU mode, the unit will return to the previous selection screen.
• By pressing the
GlideTouch bar
under RETURN in the MENU
mode, the unit will return to the normal mode.
• If no operation is performed in 60 seconds, the unit will return to
the normal mode.
• About the 2way/3way system
You can switch to 2way/3way system mode with the 2way/3way
switch on the bottom side of the unit (pages 39 to 41).
When setting to “F/R/Sub-W”:
The unit can be operated in a 2 way system.
When setting to “3 WAY”:
The unit can be operated in a 3 way system.
