ALLIANCE BA120E Installation Manual Download Page 16

Page: 16 / 68

Specifications

120 Series

170 Series

200 Series

Maximum Static Back Pressure: W.C.I.
[mbar, kPa]

0.80 [2.0, 0.20]

Minimum Static Back Pressure:

W.C.I. [Millibar, kPa]

0.0 [0.0, 0.0]

Maximum Airflow: C.F.M. [L/sec.]

1400 [660]

2150 [1,010]

Heat dissipation of surface area exposed
to conditioned air: Btu/ft

[Joules/m

]

60 [680,000]

Noise level measured during operation
at operator position of 3.3 feet [1 meter]
in front of machine and 5.2 feet [1.6 me-
ters] from floor.

60 dBA

69 dBA

Door Opening Information

Door Opening Diameter: Inches [Milli-
meter]

27.0 [686]

Door Hinge Side

Right

Door Maximum Open Angle: Degrees

180

Gas Models

Gas Connection

1 NPT

Gas Burner Rating:

Btu/hr. [kW, Mj/hr.]

270,000 [79, 290]

395,000 [116, 417]

425,000 [125, 448]

Steam Models

Steam Connection

3/4 NPT inlet

3/4 NPT outlet

3/4 NPT inlet

1 NPT outlet

3/4 NPT inlet

1 NPT outlet

Steam Coil Rating at 100 psig:

Btu/hr. [kg/hr.] (recommended operating
pressure 80-100 psig)

187,500 [88.8]

265,500 [125.7]

Electric Models

Heating Element Rating: Kilowatts
(kW)

Not Applicable

NOTE: All IEC machines are shipped with an adapter to
convert the gas connection threads to BSPT (from
NPT).

Specifications and Dimensions

DO NOT COPY or TRANSMIT

Part No. 70532501ENR7

Summary of Contents for BA120E





































































Search results

Summary of Contents for BA120E

Reviews:

Related manuals for BA120E

Brands by name

Popular brands

ALLIANCE BA120E, Installation Manual

Search results

Summary of Contents for BA120E

Reviews:

Related manuals for BA120E

Brands by name

Popular brands