ALLIANCE BA120E Installation Manual Download Page 5

Page: 5 / 68

WARNING

• DO NOT operate this appliance before reading the

instruction booklet.

• DO NOT place articles on or against this appli-

ance.

• DO NOT store chemicals or flammable materials

or spray aerosols near this appliance.

• DO NOT operate with panels, covers or guards re-

moved from this appliance.

• DO NOT load materials containing flammable sol-

vents into this appliance.

• If repeated ignition reset is required, the dryer

should not be used and a service call booked.

Risk of fire/flammable material.

W926

The following information applies to the state of Massachusetts,
USA.
• This appliance can only be installed by a Massachusetts li-

censed plumber or gas fitter.

• This appliance must be installed with a 36 inch [91 cm] long

flexible gas connector.

• A “T-Handle” type gas shut-off valve must be installed in the

gas supply line to this appliance.

• This appliance must not be installed in a bedroom or bath-

room.

DO NOT COPY or TRANSMIT

Part No. 70532501ENR7

Summary of Contents for BA120E





































































Search results

Summary of Contents for BA120E

Reviews:

Related manuals for BA120E

Brands by name

Popular brands

ALLIANCE BA120E, Installation Manual

Search results

Summary of Contents for BA120E

Reviews:

Related manuals for BA120E

Brands by name

Popular brands