ALLIANCE BA120E Installation Manual Download Page 6

Page: 6 / 68

Table of Contents

Introduction

...........................................................................................

Model Identification

.......................................................................................

Contact Information

......................................................................................

Manufacturing Date

......................................................................................

Safety Information

................................................................................

Explanation of Safety Messages

.....................................................................

Important Safety Instructions

.........................................................................

Specifications and Dimensions

..............................................................

Specifications and Dimensions

......................................................................

Cabinet Dimensions and Exhaust Outlet Locations

..........................................

Electric and Gas Connection Locations for Gas Models

...................................

Electric and Steam Connection Locations for Steam Models

............................

Electric Connection Location for Electric Models

............................................

Installation

...........................................................................................

Pre-Installation Inspection

.............................................................................

Location Requirements

..................................................................................

Remove Shipping Materials

...........................................................................

Position and Level the Tumble Dryer

..............................................................

Mounting

.....................................................................................................

Fire Suppression System (Optional Equipment)

...............................................

Check Local Codes and Permits

..................................................................

Water Requirements

...................................................................................

Water Connections

.....................................................................................

Electrical Requirements

.............................................................................

Auxiliary Alarm

........................................................................................

Before Placing Tumble Dryer into Service

.......................................................

Required for IEC Models Only

..................................................................

Exhaust Requirements

..........................................................................

Exhaust Requirements

...................................................................................

Layout

.........................................................................................................

Make-Up Air

................................................................................................

Venting

........................................................................................................

Individual Venting

.....................................................................................

Manifold Venting

......................................................................................

All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.

DO NOT COPY or TRANSMIT

Part No. 70532501ENR7

Summary of Contents for BA120E





































































Search results

Summary of Contents for BA120E

Reviews:

Related manuals for BA120E

Brands by name

Popular brands

ALLIANCE BA120E, Installation Manual

Search results

Summary of Contents for BA120E

Reviews:

Related manuals for BA120E

Brands by name

Popular brands