Algema BLITZLADER 2, Operating Instructions Manual

Page: 97 / 108

7 Additional information Eder GmbH
96 / 108 Operating Instructions Algema Blitzlader 2 Air - Edition 04/2021
Error Cause Remedy Chapter
Freewheel activated Deactivating the
freewheel on the
rope winch
Operating
instructions of the
winch
Buttons on the
manual control panel
and on the radio
remote control do not
respond
Use the enclosed
cable remote control
of the cable winch
as an emergency
operation.
See "Emergency
operation of rope
winch", page 56
Warning tone
sounds when
parking brake is
released
Plateau is not full-
constantly tilted
down
Tilt the plateau
completely until the
tilting shear has
passed the dead
center.
See "Tilt plateau
operation ", page
21
Sensor tilt shear
closed does not
respond, although
the plateau is
completely tilted
down
Check the setting,
control LEDs on
the sensor must
light up when the
plateau is
completely tilted
down.
see pictures below
sensors
Service lamp on the
touch panel lights
up in conjunction
with the "Left side"
or "Right side"
display
A warning tone
sounds when the
ignition is switched
Air pressure in air
suspension too low
Check air pressure
and check if
necessary
See "Air
suspension," page
70
Checking the status
LED on the power
unit
Status LED no. 10
must be green,
contact specialist
workshop if
necessary.
see "Power unit",
page 83
Manual control re-
does not act
Set-up functions
are not switched
on
Switching on the
setup functions on
the touch panel
See "Tilt plateau
operation ", page
21
Function for
manual control not
selected
Activate the
function of the
manual control on
the touch panel.
See "Tilt plateau
operation ", page
21
Status LED on
power unit lights up
red
Status LED no. 08
must be green,
contact specialist
workshop if
necessary.
see "Power unit",
page 83
Radio remote
control does not
respond
Set-up functions
are not switched
on
Switching on the
setup functions on
the touch panel
See "Tilt plateau
operation ", page
21
Eder GmbH 7 Additional information
Operating Instructions Algema Blitzlader 2 Air - Edition 04/2021 97 / 108
Error Cause Remedy Chapter
Function for radio
remote control not
selected
Activate the radio
remote control
function on the
touch panel or on
the radio remote
control.
see "Tilt plateau
operation ",
Page 21
see "Radio remote
control*", page 42
No connection to
the receiver
Reduce distance,
change position
-
Batteries of the
sen- der
Change batteries Operating
instructions for the
radio remote
control system
Status LED on
power unit lights up
red
Status LED no. 15
must be green,
contact specialist
workshop if
necessary.
see "Power unit",
page 83
For further information, refer to the separate operating
instructions for the radio remote control.
Electrohydraulics
starts immediately
and performs a
function as soon as
the body functions
on the touch panel
are switched on.
Clamp the
pushbutton to the
manual control unit
Operate all buttons
on the manual
control and ensure
that they are free to
move.
-
Lighting
according to
StVZO on rear
light bar defective
Bulb defective Change illuminant See "Changing
lamps", page 74
Fuse defective Check fuses on the
construction vehicle
and replace if
necessary.
Operating
instructions base
vehicle
Rotating beacon
does not work
Check status LEDs
on power unit
Status LEDs no. 25
and 26 must be
green, if necessary
contact truss instead
of
see "Power unit",
page 83
Work lights do not
work
Check status LEDs
on power unit
Status LEDs no. 22
and 23 must be
green, if necessary
contact truss instead
of
see "Power unit",
page 83