AKCP 5ESV-X20 User Manual Download Page 66

Page: 66 / 105

securityProbe 5ESV Manual

Updated until firmware 404m

- 66 -

4) Camera

1. Basic setup

The unit will allow for connection of up to 4 HD Digital cameras through the video inputs (V1

–

V4). In this tutorial we are going to assume you are connecting an AKCP pan/tilt HD Digital
camera, and we are connecting it to port number V4.

Once you are logged in you will be taken to the default “summary page”.

You may, or may not see the live image from the camera already. If not then click on

Camera setting and follow the instructions below.

PLEASE NOTE: The ActiveX has been recently removed from the Camera Settings
options in the Summery page, so your screen may appear differently.

This tutorial provides you the information needed to setup the camera functions.

To get to the starting point of this tutorial:



Connect camer

a to a video (“V”) port



Log into web based interface as administrator

Summary of Contents for 5ESV-X20









































































































Search results

Summary of Contents for 5ESV-X20

Reviews:

AKCP 5ESV-X20, User Manual, Page: 66 / 105

Search results

Summary of Contents for 5ESV-X20

Reviews: