AKCP 5ESV-X20 User Manual Download Page 28 | Manualshive

Page: 28 / 105

AKCP 5ESV-X20 User Manual Download Page 28

securityProbe 5ESV Manual

Updated until firmware 404m

- 28 -

The NAC or Network Access Control security feature

The  NAC  or  Network  Access  Control  feature  allows  you  to  restrict  access  to  the  web
interface  for  only  certain  IP  addresses,  or  deny  access  to  the  web  interface  for  only
certain IP addresses.

6. Setting up a sensor

In this section we will now go through the basic set up of a sensor. We will focus on the
AKCP temperature sensor; however this basic set up process is applicable to all of our
sensors. If you require information on specific functions of a particular sensor then please
download the manual for that sensor from our website, or locate it on your product CD.

a)

Plug the sensor into one of the RJ45 “intelligent sensor ports” on the rear panel of the
unit. In this example we will use port 1.

b)

Now point your browser to the IP address of the unit (default, 192.168.0.100). Next
you need to login as the administrator using your administrator password (default is
“public”). You will then be taken to the summary page. This is shown below.

«
...
26
27
28
29
30
...
»

Summary of Contents for 5ESV-X20










































































































Reviews:

No comments