AKCP 5ESV-X20 User Manual Download Page 15

Page: 15 / 105

securityProbe 5ESV Manual

Updated until firmware 404m

- 15 -

3. Firmware upgrade

Ensure you are running the latest firmware. You will also need to download the latest
firmware from our website (

http://www.akcp.com/company/firmwareupdate.htm

). Log

into our webpage using your MAC address, this is found on a sticker on the base of the
unit. After the download navigate back to the web based interface

(units IP address.

This

manual will refer to the DEFAULT IP address, 192.168.0.1 you need to substitute this for
your own IP address if you have changed it)

Please Note:

The firmware file used for the securityProbe 5ESV is the same file used to update

the securityProbe 5ES units as it uses the same iMX25 processor.

This tutorial provides you the information needed to upgrade the firmware.

To get to the starting point of this tutorial:



Click on the settings tab

Summary of Contents for 5ESV-X20









































































































Search results

Summary of Contents for 5ESV-X20

Reviews:

AKCP 5ESV-X20, User Manual, Page: 15 / 105

Search results

Summary of Contents for 5ESV-X20

Reviews: