manualshive.com logo in svg

Akai S3000XL, User Manual

The Akai S3000XL, a top-of-the-line sampler, offers unparalleled sound quality and versatility to music producers. Unlock the full potential of this iconic device with a comprehensive and detailed User Manual, available for free download at manualshive.com. Gain complete control over your music production journey with this invaluable resource.

Share
Download
background image

SINGLE MODE

Page 26

S3000XL Operator’s Manual

complex keyboard splits and layers without having to concern yourself with
the intricacies of setting keygroups within a program itself. Please note
that this parameter has no effect on single programs, it is only when two or
more programs have the same program number that it is effective.

This is an abbreviation of POLYPHONY and allows you to limit the
polyphony of a program.

This is an abbreviation of PRIORITY and allows you to set how notes will
be ‘stolen’  by other programs if the 32 voice polyphony is exceeded.
There are four settings: LOW, NORM, HIGH and HOLD. If the program is
set to LOW priority, then notes from this program will be stolen first. If set
to HIGH, then notes from other programs with lower priority will be stolen
first before they are stolen from this program. NORM is, of course, normal
priority and sets standard dynamic voice allocation and note stealing will
take place with no particular priority. If a program’s priority is set to HOLD,
then notes can only be stolen from this program by the same program.

If you are playing a complex piece of music using many programs in a
multi-timbral configuration, it is a good idea to set important programs to
HIGH or HOLD and less important, background programs to LOW. If the
piece of music is not overly complicated and polyphony is not going to be
exceeded, you may prefer just to leave the priority at the default setting of
NORM.

This is an abbreviation of TRANSPOSE and sets the basic octave range
for the program. The range is +/- 50 semitones. You will note that this is
not a pitch shift function as such but a MIDI transpose function - this
overcomes the problem of playing back samples out of their range. What
this function does is introduce an offset so that, even if you play C3 on the
keyboard, this is offset to play the samples on C4 (with a +12 setting) - it is
not playing the samples on C3 an octave higher.

NOTE: It must be said that this page is really an inheritance from earlier Akai samplers
when using multi-timbral setups. We strongly recommend that for such purposes, you use
the MULTI mode but retaining these functions ensures compatibility with data created on
earlier models. If you have used Akai samplers before, you may continue to work in this
way, of course, but, as mentioned, the new MULTI mode may be more convenient

SETTING PROGRAM LOUDNESS AND VELOCITY

In the 

 page, you may set the program’s overall loudness and velocity sensitivity:

The parameters are:

This sets the overall loudness for the program and affects the level
appearing at the main left/right outputs, the individual outputs and the
real-time digital audio output. It will also affect the level going to the
internal effects.

Summary of Contents for S3000XL


























































































































































































































































































































Reviews:

No comments

Related manuals for S3000XL

Panda-Audio Future Impact I Quick Start Manual preview
Future Impact I
Brand: Panda-Audio Pages: 2
Abstrakt Instruments Avalon Reference Manual preview
Avalon
Brand: Abstrakt Instruments Pages: 47
Elan Microelectronics EASY SOUND eSE Series Quick Start Manual preview
EASY SOUND eSE Series
Brand: Elan Microelectronics Pages: 16
Ronald JV-1080 Owner'S Manual preview
JV-1080
Brand: Ronald Pages: 183
Kasser Synths DAFM Genesis YM2612 User Manual preview
DAFM Genesis YM2612
Brand: Kasser Synths Pages: 18
Dave Smith Instruments TETR4 Operation Manual preview
TETR4
Brand: Dave Smith Instruments Pages: 72
Patching Panda VIBRAZUM Manual preview
VIBRAZUM
Brand: Patching Panda Pages: 4
Sixty Four Pixels PCLONE2 Instructions Manual preview
PCLONE2
Brand: Sixty Four Pixels Pages: 36
Sixty Four Pixels Arpie User Manual preview
Arpie
Brand: Sixty Four Pixels Pages: 40
Infinite Pasternack PE11S100 Series User Manual preview
Pasternack PE11S100 Series
Brand: Infinite Pages: 31
CES CEM3394 Quick Start Manual preview
CEM3394
Brand: CES Pages: 7
Behringer SYSTEM 15 Quick Start Manual preview
SYSTEM 15
Brand: Behringer Pages: 7

Brands by name

Popular brands

Load more brands