manualshive.com logo in svg

Akai S3000XL, User Manual

The Akai S3000XL, a top-of-the-line sampler, offers unparalleled sound quality and versatility to music producers. Unlock the full potential of this iconic device with a comprehensive and detailed User Manual, available for free download at manualshive.com. Gain complete control over your music production journey with this invaluable resource.

Share
Download
background image

EFFECTS EDIT

S3000XL Operator’s Manual

Page 183

STEREO PITCH SHIFT EFFECTS

If you selected PITCH SHIFT in the 

 field, the screen will look like this:

The pitch shifter allows you to set an interval for left and right. More often than not, a
small amount of detune is set here (i.e. LEFT = -00.05/RIGHT = +00.05) but you can also
set these parameters to specific intervals such as a fifth (+07.00) or an octave (+12.00) or
whatever.

NOTE: As with all but the most expensive pitch shifters, there is a small delay in the pitch
shifted sound. This can be used to enhance an ensemble effect, however. Also, extreme
pitch shifts will exhibit some ‘wobbly’ artefacts. In this case, mix the level of the pitch
shifted signal back a bit.

If you select PITCH SHIFT+FBK (pitch shift plus feedback) in the 

 page, you will

see this screen.

This is exactly the same as before and you may set the pitch shift interval as described
above. However, in the PITCH SHIFT+FB selection, you also have access to a delay line.
The delay parameters allow you to set a delay time for the feedback loop. This effects
selection looks like this as a block diagram:

SHIFT LEFT

SHIFT RIGHT

DELAY L

DELAY R

Audio in

FBK L

FBK R

The signal from the pitch shifter is fed back into itself via a delay time. If you can imagine
it - the sound goes through the pitch shifter and, after a delay, that pitch shifted sound is
fed back into the pitch shifter where it is further pitch shifted. After a delay, it is fed back
again after the delay and shifted again. The amount of feedback and the delay time for
each channel is separately variable and this gives rise to all sorts of weird and wonderful
arpeggio effects.

Summary of Contents for S3000XL


























































































































































































































































































































Reviews:

No comments

Related manuals for S3000XL

Roland EP-09 Owner'S Manual preview
EP-09
Brand: Roland Pages: 8
HP HP 8904A Service Manual preview
HP 8904A
Brand: HP Pages: 139
HP 3325A Calibration Manual preview
3325A
Brand: HP Pages: 23
HP 3326A Operating And Reference Manual preview
3326A
Brand: HP Pages: 146
HP 3320A Operating And Service Manual preview
3320A
Brand: HP Pages: 179
HP HP 8904A Operation And Calibration Manual preview
HP 8904A
Brand: HP Pages: 281
Kenwood TK-805D Instruction Manual preview
TK-805D
Brand: Kenwood Pages: 15
Kenwood TK-805D Service Manual preview
TK-805D
Brand: Kenwood Pages: 63
Arturia Phaser BI-TRON User Manual preview
Phaser BI-TRON
Brand: Arturia Pages: 38
Arturia MatrixBrute Manual preview
MatrixBrute
Brand: Arturia Pages: 21
Yamaha PF10 Owner'S Manual preview
PF10
Brand: Yamaha Pages: 8
Yamaha PF-1500 Operating Manual preview
PF-1500
Brand: Yamaha Pages: 21
Yamaha PF-70 Owner'S Manual preview
PF-70
Brand: Yamaha Pages: 35
Roland E-66 Owner'S Manual preview
E-66
Brand: Roland Pages: 118
Kawai K1-II Owner'S Manual preview
K1-II
Brand: Kawai Pages: 58
Kawai Synthesizer-100F Owner'S Manual preview
Synthesizer-100F
Brand: Kawai Pages: 28
Dave Smith Instruments Prophet 08 PE Operation Manual preview
Prophet 08 PE
Brand: Dave Smith Instruments Pages: 64
Dave Smith Instruments TETR4 Operation Manual preview
TETR4
Brand: Dave Smith Instruments Pages: 72

Brands by name

Popular brands

Load more brands