manualshive.com logo in svg

Akai MPC 3000, Operator'S Manual, Page: 83 / 276

Share
Download
Akai MPC 3000 Operator'S Manual Download Page 83

Chapter 3: Recording Sequences

Page 70

Recording MIDI System-Exclusive Data

The MPC3000 can record patch data or any other MIDI system-
exclusive messages from external synthesizers directly into tracks.
To do this, simply send the system-exclusive message to the
MPC3000 while in Record, Overdub, or Step Edit mode, and it will
be recorded into the active track, just the same as any other MIDI
data. The only limitation is that the message must be smaller than
1000 bytes. If an attempt is made to record a message that is larger
than that, the entire message will be rejected. 1000 bytes is enough
to accommodate a single voice patch data dump from virtually any
synthesizer, but it is not large enough for many voice bank data
dumps (large files containing an entire bank of synthesizer patches).

One way of using this feature is to insert a blank bar at the begin-
ning of your sequence and record the voice data dumps for each
track into that first bar. When the sequence is played from the start,
each external synthesizer will immediately receive the voice data in
the first bar, so it will be ready to play the note data starting in the
second bar with the proper sound.

There is one problem with playing system-exclusive messages from
sequences: there is no standard method for identifying the MIDI
channel number within the message, and therefore the MPC3000
cannot assign the output MIDI channel over which the message will
be sent. This means, for example, that a system-exclusive message
received over MIDI channel 3 while recording into the MPC3000
will always be played out of the MPC3000 on MIDI channel 3,
regardless of the track’s output MIDI channel. To overcome this
problem, you must send the system-exclusive message on the
desired MIDI channel while recording it into the MPC3000. Most
synthesizers allow you to select the transmit channel. Note, how-
ever, that some older synthesizers, such as the original Yamaha DX-
7, always transmit on MIDI channel 1.

However, there is a way to change the MIDI channel of a system-
exclusive message while it is in the MPC3000—by using Step Edit.
The MIDI channel is assigned to a single byte within the message
and the Step Edit function allows you to change the contents of any
byte within the message. If you know which byte a particular
manufacturer uses for the channel number, you can change the
contents of that byte to the desired MIDI channel number. For
example, the Yamaha DX-7 system-exclusive messages contain the
MIDI channel in byte number 3, so whatever number you put into
byte number 3 of the message will be the new output MIDI channel
number. To learn more about editing in Step Edit mode, read “The
STEP EDIT Key” section in the “Editing Sequences” chapter of this
manual.

Summary of Contents for MPC 3000





















































































































































































































































































Reviews:

No comments