AKA SIGNUM MFD 7272M CLASSIK Manual Download

Page: 62 / 65

Departement of international trade:

https://aka-md.com

| +74957991510 |

[email protected]

Attention!

When using a search coil with a low frequency excitation current

VDI readings will have lower values. Conversely, for higher frequency the

VDI readings will be higher.

WARRANTY INFORMATION

Manufacturer guarantees operational capability of the metal detector

provided that the consumer follows operation conditions. Warranty

period 24 months starting from the sale date.

Manufacturing defects shall be repaired by the Manufacturer during

the warranty period free of charge provided that there is no damages in

electronic module and searchcoil.

This Operating Manual with the sale date mark should be provided to-

gether

with the device in case of warranty repair. Warranty period is

cal-culated from the date of manufacture in case there is no sale date

mark.

For warranty questions, please contact:

Departement of international trade:

Site:

https://aka-md.com

Em@il:

[email protected]

Tel/WhatsApp:

+79037991510

FORUM:

https://aka-md.com/forum/

Summary of Contents for SIGNUM MFD 7272M CLASSIK


































































Search results

Summary of Contents for SIGNUM MFD 7272M CLASSIK

Reviews:

Related manuals for SIGNUM MFD 7272M CLASSIK

Brands by name

Popular brands

AKA SIGNUM MFD 7272M CLASSIK, Manual

Search results

Summary of Contents for SIGNUM MFD 7272M CLASSIK

Reviews:

Related manuals for SIGNUM MFD 7272M CLASSIK

Brands by name

Popular brands