manualshive.com logo in svg

AJA kumo 1604, Installation And Operation Manual, Page: 10 / 73

Share
Download
AJA kumo 1604 Installation And Operation Manual Download Page 10

KUMO SDI Routers and Control Panels v4.7r1 10 www.aja.com

 

KUMO Control Panel Connections

Similar to the KUMO router, KUMO CP has an RJ-45 Ethernet connector and power 

supply connectors, but has no BNC connectors and no RS-422 port. 

KUMO Control and Monitoring 

The KUMO router user-interface provides powerful remote setup, control, and 

monitoring with:

•  Zero-configuration Bonjour Protocol and support for UPnP networking 

protocols

•  Remote web browser control interface via Ethernet
•  Optional KUMO CP (32 button) and KUMO CP2 (64 button) hardware control 

panels, each unit able to control up to four KUMO routers

NOTE:  The 32 button KUMO CP hardware Control Panel can be used with a KUMO 6464 

router operating in Normal mode, but can only control the first 32 Sources and 

Destinations. The KUMO CP can be used to fully control a KUMO 6464 that is 

operating in Dual or Quad mode. Control of the KUMO 6464 router in all modes 

is available via the KUMO CP2 64 button hardware panel, web browser, Ethernet 

control, and RS-422. 

•  GVG Native Protocol built-in to allow serial or LAN interconnection (one 

RS-422 or up to 32 Ethernet) and interoperability with other equipment. 

Specifically, KUMO can be controlled by the SMS 7000 portion of the GVG 

Native Protocol. For details, refer to: 

"GVG Native Protocol Support" on page 

61

. 

Default Network Settings

KUMO routers and control panels ship with DHCP enabled, making system 

operation possible simply by connecting the KUMO device’s Ethernet cabling. 
In addition, temporary default static IP addresses can be activated for initial 

KUMO system configuration. See 

"KUMO Temporary Static IP Address" on page 14

.

In This Manual

Chapter 1: Introduction lists features and gives a general description of the 

product.
Chapter 2: Installation details KUMO installation, connections, and networking 

configuration options.
Chapter 3: Web Browser User Interface provides complete instructions for 

controlling and monitoring the KUMO router from a computer.
Chapter 4: KUMO Remote Control Panels details the configuration and operation 

of the optional KUMO CP and CP2 Control Panels. 
Appendix A: Specifications lists technical specifications for the products.
Appendix B: Safety and Compliance information.
Warranty and Index

Summary of Contents for kumo 1604










































































Reviews:

No comments