manualshive.com logo in svg

Air Live POE-FSH2422G-250, User Manual, Page: 43 / 51

Share
Download
Air Live POE-FSH2422G-250 User Manual Download Page 43

4. Web Management 

 
 
 
 
 

 

AirLive POE-FSH2422G-250 User’s Manual 

 

38

4.31 STP Bridge Settings 

(QoS Setting)

 

 

 

„

  Bridge Priority: This parameter configures the spanning tree priority globally for this 

switch. The device with the highest priority becomes the STP root device. However, if all 

devices have the same priority, the device with the lowest MAC address will then 

become the root device. Number between 0 - 61440 in increments of 4096. Therefore, 

there are 16 distinct values. 

„

  Hello Time: Interval (in seconds) at which the root device transmits a configuration 

message (BPDU frame). Number between 1-10 (default is 2). 

„

  Max Age – The maximum time (in seconds) a device can wait without receiving a 

configuration message before attempting to reconfigure. That also means the maximum 

life time for a BPDU frame. Number between 6-40 (default is 20). 

„

  Forward Delay: The maximum time (in seconds) the root device will wait before 

changing states (i.e., discarding to learning to forwarding). Number between 4 – 30 

(default is 15) 

 

Summary of Contents for POE-FSH2422G-250




















































Reviews:

No comments