manualshive.com logo in svg

Air Live POE-FSH2422G-250, User Manual, Page: 13 / 51

Share
Download
Air Live POE-FSH2422G-250 User Manual Download Page 13

2. Installation of the Switch 

 

AirLive POE-FSH2422G-250 User’s Manual 

 

8

1000BASE-T Gigabit Ethernet Ports (Port 25~26): 

The Switch provides two Gigabit twisted pair ports, supported auto negotiable 

10/100/1000Mbps and auto MDI/MDIX crossover detection function, this function gives true 

“plug and play” capability, just need to plug-in the network cable to the hub directly and 

don’t care if the end node is NIC (Network Interface Card) or switch and hub. These ports 

can operate in half-duplex mode for 10/100Mbps and full- duplex mode for 

10/100/1000Mbps. 

Note: When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled. 

 

Combo mini-GBIC Ports (Port 25~26) 

The Switch is equipped with two combo mini-GBIC ports, supported optional 

1000BASE-SX/LX mini-GBIC module. The 1000BASE-T port 25 and 26 are the same ports 

with the mini-GBIC port 25 and 26, when plug in the mini-GBIC module, the device will 

activate mini-GBIC, and the RJ45 port will be disabled. 

 

Reset: 

The Reset button is to reset all the setting back to the factory default. 

Note: Be sure that you recorded the setting of your device, else all the setting will be erased 

when pressing the “Reset” button. 

 

The Rear Panel 

The 3-pronged power plug is placed at the rear panel of the switch right side shown as 

below. 

 

 

 

 

 

Summary of Contents for POE-FSH2422G-250




















































Reviews:

No comments