manualshive.com logo in svg

Air Live POE-FSH2422G-250, User Manual, Page: 30 / 51

Share
Download
Air Live POE-FSH2422G-250 User Manual Download Page 30

4. Web Management 

 
 
 
 
 

 

AirLive POE-FSH2422G-250 User’s Manual 

 

25

 

 

„

  Auto-Negotiation: Enable and Disable. Being set as ‘Enable’, the Speed, Duplex mode, 

Pause, Backpressure, TX Capability and Address Learning are negotiated automatically. 

When you set it as ‘Disable’, you have to assign those items manually. 

„

  Speed: When the Auto-Negotiation column is set as Disable, users have to set the 

connection speed to the ports ticked. 

„

  Duplex: When the Auto-Negotiation column is set as Disable, users have to set the 

„

 

„

 

alf-duplex 

„

 

otiation column is set as Disable, users have to 

„

 

„

 

date to have the configuration take effect. 

„

  Setting Status: Displays current status. 

Clic

 effective 

 

connection mode in Half/Full to the ports ticked. 

Pause: Flow Control for connection at speed of 10/100Mbps in Full-duplex mode. 

Backpressure: Flow Control for connection at speed of 10/100Mbps in H

mode. 

TX/RX Capability: When the Auto-Neg

set this column as Enable or Disable. 

Addr. Learning: When the Auto-Negotiation column is set as Disable, users have to set 

this column as Enable or Disable. 

„

  Select Port No.: Tick the check boxes beside the port numbers being set. 

Click Up

„

  Current Status: Displays current port status. 

k Update to make the configuration

Summary of Contents for POE-FSH2422G-250




















































Reviews:

No comments