manualshive.com logo in svg

Air Live POE-FSH2422G-250, User Manual, Page: 17 / 51

Share
Download
Air Live POE-FSH2422G-250 User Manual Download Page 17

2. Installation of the Switch 

 

AirLive POE-FSH2422G-250 User’s Manual 

 

12

The following table summarizes the cable requirement for 10/100/1000BASE-TX 

connection: 

 

10BASE-T 

100 ohm Category 3, 4, 5 UTP/STP 

cable 

100BASE-TX 

100 ohm Category 5 UTP/STP cable 

1000BASE-T 

100 ohm Category 5E UTP/STP cable 

or better   

 

Auto MDI/MDI-X function 

 

The POE-FSH2422G-250 PoE Switch is equipped with Auto-MDI/MDI-X function, which 

allows you to use straight-thru cable even when connecting to another switch/hub.  Simply 

use the straight-through cable for all types of 10/100BASE-TX connections, either to a PC 

or to a networking device such as other hub or switch. 

 

Connection 

Specification 

10 /100Base-TX and 1000Base-T 

Ports 

Interface 

RJ-45 

Cable to Use 

 

      To an end station 

Straight-through twisted-pair cable 

      To a hub/switch 

Straight-through twisted-pair cable 

Maximum Distance 

100 meters 

 

 

 

2.7 Connecting to Power 

POE-FSH2422G-250 PoE Switch features a universal auto-select power supply unit, which 

allows a power connection to a wide range of input voltages from 100 to 240VAC @ 50 ~ 

60Hz. 

To establish its power connection, simply plug the female end of the power cord into the power connector on the rear of 

the switch and the male end of the power cord into a suitable power outlet.    Once you have correctly plugged in the 

power, you can then turn on the Power Switch to activate the switch.

 

Summary of Contents for POE-FSH2422G-250




















































Reviews:

No comments