manualshive.com logo in svg

Air Live POE-FSH2422G-250, User Manual, Page: 34 / 51

Share
Download
Air Live POE-FSH2422G-250 User Manual Download Page 34

4. Web Management 

 
 
 
 
 

 

AirLive POE-FSH2422G-250 User’s Manual 

 

29

„

  Multi to 1 Setting 

In the following sessions, we will talk in detail about the management functions under the 

 

„

 VLAN 

Mode 

„

 VLAN 

Member 

VLAN Setting menu.

 

 

4.18 VLAN Mode (VLAN Setting) 

 

ort-based VLAN is for separating traffic only 

etwork traffic within VLAN groups to other 

switches. For the handover to other switches use Tag Based VLAN. In VLAN Mode you can 

ince here the 

andover between the switches of your network takes place. 

You may select the VLAN Mode of the switch. P

on this single switch. There is no handover of n

switch from Tag to Port Based VLAN. Port Based VLAN is the default mode. 

 

After switching to Tag Based VLAN Mode, the screen changes. On this screen you can 

now define and configure your Up- and Downlink ports. These are important s

h

 

 

 

„

  VLAN Mode: Displays VLAN mode: port based/Tag based VLAN. Here you can also 

switch back to Port Based VLAN Mode 

„

  Add tag means the outgoing packet of the selected port will be inserted a 802.1Q tag. 

 

Use this setting for your Up- and Downlink Ports in your VLAN Tagged Network. 

Summary of Contents for POE-FSH2422G-250




















































Reviews:

No comments