Air Live POE-FSH2422G-250 User Manual Download Page 33 | Manualshive

Page: 33 / 51

Air Live POE-FSH2422G-250 User Manual Download Page 33

4. Web Management

AirLive POE-FSH2422G-250 User’s Manual

28

m

Enable Port: Having ticked the boxes, the port will stop transmitting or receiving data

Click Update to have the configuration take effect.

Threshold: Type in the threshold in the range between 1 and 63 to limit the maximu

byte counts, which a port can send or receive in a period of time.

when their sending byte counts or receiving byte counts reach the defined threshold.

4.16 OE (Port Management menu)

P

is page and also enable or disable per

port.

User could know per PoE port out power status in th

4.17 VLAN Setting

A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which

twork traffic, so only the members of the same VLAN will

receive traffic from the ones of the same VLAN. Basically, creating a VLAN from a switch is

would allow you to isolate ne

logically equivalent of reconnecting a group of network devices to another Layer 2 switch.

However, all the network devices are still plugged into the same switch physically.

There are many management functions can be set or performed if you click the

VLAN Setting on Home Page, including:

«
...
31
32
33
34
35
...
»

Summary of Contents for POE-FSH2422G-250




















































Reviews:

No comments