Agilent Technologies G7104A User Manual Download Page 69

Page: 69 / 234

Agilent 1290 Infinity II Flexible Pump User Manual

Error Information

Pump Error Messages

Reading of multi purpose valve tag failed

Error ID: 29240

Reading the multi purpose valve tag failed.

•

Parameter: None

Pump drive encoder rollover

Error ID: 29232

Invalid pump drive encoder signals have been detected.

•

Parameter: 1 – 2 referring to pump drive

Probable cause

Suggested actions

Reading of multi purpose valve tag failed.

Check cable connection.

Multi purpose valve head tag defect or
empty.

Replace multi purpose valve head.

Multi purpose valve tag reader is defect.

Please contact your Agilent service
representative.

Probable cause

Suggested actions

Pump drive encoder is defect.

Please contact your Agilent service
representative.

Summary of Contents for G7104A











































































































































































































































Search results

Summary of Contents for G7104A

Reviews:

Brands by name

Popular brands

Agilent Technologies G7104A, User Manual

Search results

Summary of Contents for G7104A

Reviews:

Brands by name

Popular brands