manualshive.com logo in svg

Agilent Technologies G7104A, User Manual

Share
Download
Agilent Technologies G7104A User Manual Download Page 203

Agilent 1290 Infinity II Flexible Pump User Manual

203

LAN Configuration

11

Automatic configuration with Bootp

Installation of BootP Service

Before installing and configuring the Agilent BootP Service, be sure to 
have the IP addresses of the computer and instruments on hand.

1

Log on as Administrator or other user with Administrator privileges.

2

Close all Windows programs.

3

Insert the Agilent ChemStation software DVD into the drive. If the 
setup program starts automatically, click 

Cancel

 to stop it.

4

Open Windows Explorer.

5

Go to the BootP directory on the Agilent ChemStation DVD and 
double- click 

BootPPackage.msi

.

6

If necessary, click the 

Agilent BootP Service...

 icon in the task bar.

7

The 

Welcome

 screen of the 

Agilent BootP Service Setup Wizard

 appears. Click 

Next

.

8

The 

End-User License Agreement

 screen appears. Read the terms, indicate 

acceptance, then click 

Next

.

9

The 

Destination Folder

 selection screen appears. Install BootP to the 

default folder or click 

Browse

 to choose another location. Click 

Next

.

The default location for installation is:

C:\Program Files\Agilent\BootPService\

10

Click 

Install

 to begin installation.

Summary of Contents for G7104A











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands