manualshive.com logo in svg

Advantech DLT-V6210, Manual

Share
Download
Advantech DLT-V6210 Manual Download Page 58

End-of-life device disposal 

 

Page 58 / 61 

DLT-V6210 Manual V1.00 

© by DLoG GmbH 

Wi-Fi special regulations for Germany and France 

For DLT-V6210 with Wi-Fi 802.11a/b/g/n, the following restrictions to be applied: 

−

 

In Germany, Wi-Fi 5 GHz band: 5.15 GHz – 5.35 GHz may only be used indoors. 

−

 

In France, Wi-Fi operation outdoors is only permitted in the 2454 – 2483.5 MHz range at max. 

10 mW EIRP. 

 

 

16.4.  CE marking 

The devices of DLT-V6210 series were tested and fulfill the CE conformity requirements and carry the 

CE mark on the rear side of the device. 

 

 

16.5.  Taiwan BSMI screen warning 

  WARNING 

使用過度恐傷害視力. 

 

ATTENTION / NOTICE 

使用 30 分鐘請休息 10 分鐘. 
未滿 2 歲幼兒不看螢幕，2 歲以上每天看螢幕不要超過 1 小時. 

 

 

 

 

 

 

17. 

End-of-life device disposal 

 

 

 

 

DLT-V6210 devices which are defective or ready for disposal which should be 

considered as special waste and can be recycled. They must not be disposed as 

general/domestic waste. 

Proper disposal in accordance with local regulations is required. 

Please contact the responsible authorities in your country/region to find out about 

the applicable regulations, if necessary. 

 

 

 

Summary of Contents for DLT-V6210






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands