manualshive.com logo in svg

Advantech DLT-V6210, Manual

Share
Download
Advantech DLT-V6210 Manual Download Page 31

 

Electrical installation, cable connection, cable cover 

© by DLoG GmbH 

DLT-V6210 Manual V1.00 

Page 31 / 61 

8.5. 

Connecting the USB, Ethernet and COM cables 

 

NOTICE: Physical damage 

Observe the following instructions when connecting/removing external devices to/from  

DLT-V6210. 

 

Only use accessories that have been tested and approved by Advantech-DLoG for the 

respective DLT-V6210.  

 

DLT-V6210 may not be connected to the power supply if external devices are being 

connected/removed (not applicable for USB devices) 

 

Otherwise considerable damage could be caused to both DLT-V6210 and the peripheral 

devices. 

 

Make sure that peripherals with their own power supply are either switched on at the same 

time as DLT-V6210 or after the start of DLT-V6210.  

 

Otherwise, you must ensure that the backflow from the external device to DLT-V6210 

cannot take place. 

 

Only power up DLT-V6210 when all devices are completely connected and DLT-V6210 is 

closed correctly (remember the cable cover!). Otherwise, you may damage DLT-V6210. 

 

 

 

Please observe the mounting instructions supplied with the optional accessory. 

 

 

8.5.1. 

USB cable 

 

Attach the matching cable grommet to the USB cable.  

NOTICE

: Opening of the cable grommet must be slightly smaller than the cable diameter. 

 

Insert the cable grommet including the USB cable into the cable pass-through 

 

Place one cable clip on the USB cable. 

 

Secure the cable clip to the strain relief rail using 2 mounting screws (M3x10 screws). 

 

Tighten the mounting screws alternatingly. 

 

ATTENTION:

 Screw on sufficiently but make sure that the cable is not pinched or damaged. 

 

Fig. 8.7: USB cable on the connector panel; secured to the strain relief rail 

 

 

 

Summary of Contents for DLT-V6210






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands