manualshive.com logo in svg

Advantech DLT-V6210, Manual

Share
Download
Advantech DLT-V6210 Manual Download Page 33

 

Electrical installation, cable connection, cable cover 

© by DLoG GmbH 

DLT-V6210 Manual V1.00 

Page 33 / 61 

8.5.3. 

COM cable 

 

Attach the matching cable grommet to the COM cable.  

NOTICE

: Opening of the cable grommet must be slightly smaller than the cable diameter. 

 

Insert the cable grommet including the COM cable into the cable pass-through 

 

Place one cable clip on the COM cable. 

 

Secure the cable clip to the strain relief rail using 2 mounting screws (M3x10 screws). 

 

Tighten the mounting screws alternatingly. 

 

ATTENTION:

 Screw on sufficiently but make sure that the cable is not pinched or damaged. 

 

Fig. 8.9: COM cable on the connector panel; secured to the strain relief rail 

 

 

8.6. 

Closing off unused cable compartment openings 

 

 

Close off all unused cable compartment openings with the dummy grommet so that they are sealed. 

Fig. 8.10: Unused cable outlets sealed off with dummy grommet 

 

 

 

 

 

 

 

 

 

Summary of Contents for DLT-V6210






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands