manualshive.com logo in svg

Advantech DLT-V6210, Manual

Share
Download
Advantech DLT-V6210 Manual Download Page 42

External connectors 

 

Page 42 / 61 

DLT-V6210 Manual V1.00 

© by DLoG GmbH 

10.2.  CFast slot under the antenna cap 

There is a CFast slot under the antenna cap. 

 

Exercise special care when removing and re-inserting CFast card. 

 

Only use CFast cards that have been approved by Advantech-DLoG. 

 

 

NOTICE: Physical damage 

Improper opening of the antenna cap can impair the function of entire DLT-V6210 system and in 

particular the Wi-Fi functionality. 

−

 

The antenna cap may only remain open during the service work.  

−

 

No objects or liquids may enter the opened DLT-V6210 during this. 

−

 

Only when the antenna cap is properly closed again may operation be resumed; the 

protection class/category is only ensured again after doing so. 

 

 

10.3.  Opening/closing the antenna cap 

Opening 

 

Loosen the two screws of the antenna cap using Torx screwdriver. 

 

Carefully lift up the antenna cap.  

 

Fig. 10.4: Antenna cap opened 

 

 

 

Closing 

 

Place the antenna cap back onto DLT-V6210. 

 

The antenna cap seal must not be damaged; it must be seated correctly in the groove. 

 

Tighten the two screws of the antenna cap again (1 Nm torque). 

 

 

 

 

 

 

Summary of Contents for DLT-V6210






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands