Accurate Technology ProPanel Classic Instruction Manual Download Page 39

Page: 39 / 44

ProPanel Classic

Page 39 of 44

Pr35

–

External Key Input 1

[0 to 11]

This parameter maps the Auxiliary Key to be activated externally.

Default Value = 0

Pr36

–

External Key Input 2

[0 to 11]

This parameter maps the Auxiliary Key to be activated externally.

Default Value = 0

Pr37

– Programmable Output Polarity

[0 or 1]

This sets the normal state of the programmable output when

not

activated

and
Circuit board jumper

is in position

Default Value = 0

Pr38

– Programmable Output Function

[0 to 3]

Selects the function that the programmable output activates on when Circuit
board jumper

is in position

Default Value = 0

Value of Pr 38

Function

No Operation

Monitor (Drift) Operation

Upper/Lower Limits

Go/No Go

Value of Pr 35 & 36

Key

None

On/Off

Units

Plus

Datum

Minus

ABS/INC

Send

Pr 37 Setting

Output Polarity

Normally Open (NO)

Normally Closed (NC)

Summary of Contents for ProPanel Classic













































Search results

Summary of Contents for ProPanel Classic

Reviews:

Related manuals for ProPanel Classic

Brands by name

Popular brands

Accurate Technology ProPanel Classic, Instruction Manual

Search results

Summary of Contents for ProPanel Classic

Reviews:

Related manuals for ProPanel Classic

Brands by name

Popular brands