Accurate Technology ProPanel Classic Instruction Manual Download Page 32

Page: 32 / 44

P/N 800-1090-104 Rev L102012

Page 32 of 44

Enter Programming Mode

Press and Hold

the

UNITS

key while

Momentarily

pressing the

DATUM

key.

The LCD will briefly display:

PG on

(Programming On). Release both keys.

The LCD will then display

Pr 1

, (indicating Programming Parameter #1) for

about 1 second, then display the value stored for

Pr1

Video demonstration

Navigating Programming Mode:

To move up Parameter list:

Momentarily

press the

UNITS

key to advance up through the

Programming Parameter list. The Readout will display the Parameter
number, then the current programmed value.

To move down Parameter list:

Press and Hold

the

OFF

key and

Momentarily

press

the

UNITS

key to move backward through the Parameter

list.

To Increase a Parameter value:

Momentarily

press the

plus (+)

key while the Parameter value is

displayed.

To Decrease Parameter value:

Momentarily

press the

minus (-)

key while the Parameter value is

displayed.

To Reset a Parameter value to the Factory Default setting:

Momentarily

press the

DATUM

key while the Parameter value is

displayed.

Momentarily press

Press & Hold

Summary of Contents for ProPanel Classic













































Search results

Summary of Contents for ProPanel Classic

Reviews:

Related manuals for ProPanel Classic

Brands by name

Popular brands

Accurate Technology ProPanel Classic, Instruction Manual

Search results

Summary of Contents for ProPanel Classic

Reviews:

Related manuals for ProPanel Classic

Brands by name

Popular brands