Accurate Technology ProPanel Classic Instruction Manual Download Page 26 | Manualshive

Page: 26 / 44

background image

P/N 800-1090-104 Rev L102012

Page 26 of 44

Measurement Accumulator

This Function allows multiple measurements to be
made, and the sum displayed on the Readout.

S

ET

P

ROGRAMMING

P

ARAMETER

pr24

=

3

to enable this function.

P

ROGRAMMING

P

ARAMETER

is used to configure this function.

F3 & F4

are used to execute this function.

1. Press the

F4

key to view any previous accumulator value.

The LCD will display

Accu

for 1 second followed by the total

accumulated measurements. The display format for the accumulated total
is controlled by both the currently selected measurement mode (

UNITS

key) and the Programming Parameter

a.

If

Pr25

is set to 0, and the Readout is in inch mode, (decimal or

fractions), the accumulated total is displayed in Decimal Inches.

b.

If

Pr25

is set to 0, and the Readout is in metric mode, (mm or cm),

the accumulated total is displayed in mm.

c.

If

Pr25

is set to any non-zero value, and the Readout is in inch

modes, (decimal or fractions), the accumulated total is displayed
as feet and inches. (fff ii) where f=feet and i = inches

d.

If

Pr25

is set to any non-zero value, and the Readout is in metric

mode, (mm or cm), the accumulated total is displayed as meters
and millimeters. (MM mmm) where M=meters and m=millimeters.

2. Press the

F3

key to clear the accumulator.

The LCD will display

CLr

for 1 second. The DRO will return to the normal

measuring mode.

3. To add a measurement to the accumulator, make the measurement and

then press the

F3

key. The LCD momentarily displays

Add

to indicate

that the measurement has been added to the accumulated total.
Continue to add measurements by pressing the F3 key as each
measurement is made.

4. To view the accumulated total, press the

F4

key.

The following options are now available:
a. Press

F3

to clear the total and return to the measuring mode.

b. Press

F4

(DOES NOT clear the total) to return to the measuring mode.

c. Press

SEND

to transmit the accumulated total to the output port.

NOTE

: This Function maintains a running sum of the measurements taken.

Individual measurements in a series cannot be edited or deleted. If an error is
made and an incorrect measurement is taken, the entire summation must be
cleared and repeated. No rounding of inches or millimeters occurs when
configured for feet/inches or meters/millimeters.

«
...
24
25
26
27
28
...
»

Summary of Contents for ProPanel Classic













































Reviews:

No comments

Related manuals for ProPanel Classic

Brand: Yamaha Pages: 3

Blancett B3100 Series

Brand: Badger Meter Pages: 16

Brand: Badger Meter Pages: 26

Brand: Badger Meter Pages: 48

Brand: F&F Pages: 2

Brand: Hameg Pages: 44

Brand: Hameg Pages: 60

Brand: Hameg Pages: 28

Brand: HAMAR LASER Pages: 113

Brand: Percussion Play Pages: 3

Dusty Harp Pickup Series

Brand: Dusty Strings Pages: 5

Brand: KALEAS Pages: 64

Brand: ILX Lightwave Pages: 126

Brand: Parkside Pages: 199

Brand: Polimaster Pages: 24

LaserRange-Master T4 Pro

Brand: LaserLiner Pages: 68

Brand: VECTECH Pages: 10

G-TRAN CCMT-D Series

Brand: Ulvac Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands