Accurate Technology ProPanel Classic Instruction Manual Download Page 17 | Manualshive

Page: 17 / 44

background image

ProPanel Classic

Page 17 of 44

Linear Scaling

This function is useful when the actual measurement or position must be
multiplied or divided before being displayed on the Readout.
This function has a range of 0.0001 to 9.9999 allowing the actual measured
value to be multiplied or divided in very small or very large increments.

See

Programming Parameter (Pr13)

f

or additional information.

THIS PARAMETER HAS BEEN FACTORY SET FOR PROPANEL

Upper/Lower Limits

The standard ProPanel Readout can display either

LL

, for Lower Limit, or

UL

, for Upper Limit, if a user programmed upper or lower reading is

exceeded.
Upper and Lower Limits are set with

Programming Parameters Pr28 and Pr29

but are only active if

is set to 1. The display toggles for 2 seconds

between the current measurement and

LL

if the Lower Limit is exceeded, (or

UL

if the Upper Limit is exceeded. This continues as long as either limit is

exceeded.

See

Programming Parameters (Pr27, 28, 29)

for additional information.

«
...
15
16
17
18
19
...
»

Summary of Contents for ProPanel Classic













































Reviews:

No comments

Related manuals for ProPanel Classic

Brand: Kane Pages: 4

Brand: Abbott Pages: 296

Brand: DAVIS Pages: 12

Brand: Lumel Pages: 32

Brand: Vega Pages: 28

Brand: Vega Pages: 20

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: Sensia Pages: 139

Brand: York Pages: 2

Brand: Hilti Pages: 31

Brand: Dynojet Pages: 88

Brand: VP instruments Pages: 15

Brand: DODODUCK Pages: 2

Brand: Spasciani Pages: 26

Brand: Kane Pages: 35

Brand: Veris Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands