Accurate Technology ProPanel Classic Instruction Manual Download Page 21 | Manualshive

Page: 21 / 44

background image

ProPanel Classic

Page 21 of 44

Output Signal Polarity

The polarity of the output signal is set using

The output is a transistor that conducts to Negative. The factory default is

normally open

(NO).

NOTES

: The LCD will flash when any of the programmed conditions above

are encountered, but the output signal only changes state once and then
toggles back when an in-tolerance condition is restored.
When the Monitor mode is active AND the programmable output is enabled,
the hardware output will not become active until the error condition has lasted
at least 2 consecutive seconds.

CAUTION

:

The output signal remains active during Programming.

If parameters relating to the output are changed during Programming, the
output signal could become active!

«
...
19
20
21
22
23
...
»

Summary of Contents for ProPanel Classic













































Reviews:

No comments

Related manuals for ProPanel Classic

Brand: YOKOGAWA Pages: 3

System SourceMeter 2601B

Brand: Keithley Pages: 13

Brand: Keller-druck Pages: 8

Brand: YOKOGAWA Pages: 53

Brand: Panasonic Pages: 1

Brand: marposs Pages: 58

Brand: PASI Pages: 59

Brand: Lutron Electronics Pages: 10

Brand: Omega Pages: 4

Brand: Kawai Pages: 16

Brand: Kawai Pages: 56

Brand: Readiness Systems Pages: 16

IPA CONTROL EXACT

Brand: PITSID Pages: 11

IMI SENSORS 601A92

Brand: PCB Piezotronics Pages: 19

Brand: Gelia Pages: 4

Brand: Behringer Pages: 2

Brand: Klein Tools Pages: 14

Recurring Nightmare

Brand: FuzzDog Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands