22
23
USER MANUAL - 230 VAC MULTIFUNCTION CONTROL UNIT - 051D
REMOTE CONTROLS CONFIGURATION
This function is only available for the model WITH RADIO MODULE (APE-570/0510)
The remote controls can be configured using radio functions, which are identified on the display by the letter
r
.
r0
REMOTE CONTROL DELETION
r5
DELETE ALL REMOTE CONTROLS
po
OPEN DEAD MAN
r1
START
r6
PROGRAMMABLE FUNCTION
pc
CLOSE DEAD MAN
r2
STOP
r7
PROGRAMMABLE FUNCTION
go
START
r3
PEDESTRIAN
r9
PLUG-IN RADIO MODULE
r4
FAST CLOSURE
r1 r2 r3 r4 r6 r7
STORE A REMOTE CONTROL
Up to 99 remote controls can be stored on the control unit. The remote control code is stored in the control unit (not in the radio module).
If a remote control is to be deleted in the future, it is advisable to make a note of the memory allocation number for each user.
To store a remote control, select one of the available functions:
r1
START ,
r2
STOP,
r3
PEDESTRIAN,
r4
FAST CLOSURE,
r6
PROGRAMMABLE FUNCTION or
r7
PROGRAMMABLE FUNCTION
Having selected the function, after about 2 seconds, the display shows =_. Keep the REMOTE CONTROL KEY pressed down and simulta-
neously press the (
+
) KEY on the control unit. When a remote control is transmitting, the display indicates this by lighting up a dot on the
display. Once the remote control has been memorised, the control unit displays its identification number in the
ID memory (from 0 to 99). The identification code is useful for deleting the remote control using the function
r0.
The remote control iden-
tification number is shown each time the stored remote control is transmitted and only after
having selected one of the radio parameters
r1
,
r2
,
r3
,
r4
,
r6
or
r7
. If the key on the remote control is pressed when the control
unit is in STAND BY
- -
the message of the function with which it is associated is displayed.
SAVING A REMOTE CONTROL AS START
1. Select the parameter
r1
using the scroll keys (
←
) or (
→
).
2. After a few seconds the display shows = _.
3. Hold down the button on the remote control to be stored. The display shows = . _
4. Press the (
+
) KEY on the control unit. The display shows =
1
. The remote control has been successfully stored in position 1 of the con-
trol unit memory (display =
2
memory position 2, display =
3
memory position 3, etc. up to 99).
4a. If the display shows = . , the remote control has not been stored.
4b. If the display doesn’t show = . , the remote control was not received (e.g.: different frequency from the receiver), or the radio receiver
is faulty.
r0
DELETE A REMOTE CONTROL
To delete a remote control it is necessary to know its ID (IDENTIFICATION number) or, vice versa, it is necessary to know the ID of the remote
controls you do not want to delete. To find out the ID of a remote control, select one of the following radio parameters
r1
,
r2
,
r3
,
r4
,
r6
or
r7
. Press the button on the remote control: the display will show its identification number.
To delete a remote control, select parameter
r0
. After a few seconds, the display shows in sequence the identification numbers of the
remote controls in the control unit’s memory. Once the ID of the remote control that is to be deleted
is displayed, press and hold the (
+
) KEY on the control unit. The display starts flashing and continues to show the ID number. Continue to
hold down the (
+
) KEY until the display turns off (approx. 2 seconds). The remote control has been deleted.
EXAMPLE: DELETE THE REMOTE CONTROL WITH IDENTIFICATION NUMBER 3
1. Select the parameter
r0
using the scroll keys (
←
) or (
→
).
2. After 2 seconds the control unit shows =
3. After 2 seconds the control unit shows =
1
4. After 2 seconds the control unit shows =
2
5. After 2 seconds the control unit shows =
3
6. Press and hold down the (
+
) KEY
7. The display starts flashing showing =
3
. Keep holding down the (
+
) KEY
8. After about 2 seconds the display turns off, the remote control has been deleted.
