ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 73

Page: 73 / 116

The following table illustrates the ports
used by the module:

Port

Service

Notes

502/tcp

Modbus TCP

When the module is used as a Modbus TCP/IP communication module.

80/tcp

Server HTTP

When the module is used as a Server HTTP.

319/udp

IEEE 1588

When IEEE protocol 1588 is enabled

320/udp

—
Table 5.15 Ports of Ekip Com Modbus TCP -module

LED

Indication

Description

Power LED, green

Off

Power supply absent.

On fixed

Power supply and communication

with the device present.

On, with two quick flashes per second

Power supply present, and

communication with device absent.

Link LED, green

Off

Connection error (signal absent).

On, fixed

Correct connection.

Activity LED, yellow

Off

No activity on the line.

On, flashing

Activity present on the line (in

reception and/or transmission).

—
Table 5.16 Indication / Ekip Com Modbus TCP -module

5.6.4.1 LED indications

The following table illustrates the possi-
ble signals, and their meaning:

Link

Activity

—
Fig. 5.21 Signals of Ekip Com Modbus TCP -module

CD
, T

Summary of Contents for Zenith ZTG 30





















































































































Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands

ABB Zenith ZTG 30, Operation, Maintenance And Installation Manual

Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands