ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 85

Page: 85 / 116

—

6.2 Warnings

LCD

Touch

Message

Reason

S1 and S2 not in sync

Voltage sources are not synchronized

Voltage Not Calibrated

Calibration data in power module is invalid or unavailable

Current Not Calibrated

Calibration data in current measurement module is invalid or unavailable

Pole temperature warning

Measured pole temperature is near the alarm level

Control Retry

Failed transfer sequence retry activated

Auto Control Disabled

Device is in manual operating mode

Local Bus

Module heartbeat error

Configuration

Configuration session ports are open

RTC capacitor charging

Real time clock is not yet operational, date & time setting is disabled as

long as this warning is active. RTC capacitor is charged from source

voltage (not AUX) and takes about 10 minutes.

—
Table 6.2

Warnings-list in level 3 and 4, LCD and touch control interfaces

CD
, T

Summary of Contents for Zenith ZTG 30





















































































































Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands

ABB Zenith ZTG 30, Operation, Maintenance And Installation Manual

Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands