ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 71

Page: 71 / 116

5.6.3.3 Access from the display /
Ekip Com DeviceNet –module

With modules connected and energized,
the presence of the modules on the mod-
ule slot activates additional menus on
the display.

The following table illustrates the path for
accessing the configuration parameters
of the modules from the display:

Settings (*Default value)

Description

:
Modules (Optional modules)

Ekip Com DeviceNet

MAC address

1… 63, default 63*

Address to be assigned to the
modules. IMPORTANT: devices
connected to the same network
must have different addresses

Baudrate

125 kbit/s, 250 kbit/s*, 500 kbit/s

Data transmission speed

—
Table 5.13 The path for accessing the configuration parameters of the Ekip Com DeviceNet -module from the display

The following table illustrates the path
from the display for accessing informa-
tion on the module:

About

Description

:
Modules (Optional modules)

Ekip Com DeviceNet

Serial number

Version

Software version

—
Table 5.14 Information of Ekip Com
DeviceNet -module in HMI

CD
, T

Summary of Contents for Zenith ZTG 30





















































































































Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands

ABB Zenith ZTG 30, Operation, Maintenance And Installation Manual

Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands