ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 77

Page: 77 / 116

5.6.5.1 LED indications

The following table illustrates the possi-
ble signals, and their meaning:

Link

Activity

LED

Indication

Description

Power LED, green

Off

Power supply absent.

On fixed

Power supply and communication

with the device present.

On, with two quick flashes per second

Power supply present, and

communication with device absent.

Link LED, green

Off

Connection error (signal absent).

On, fixed

Correct connection.

Activity LED, yellow

Off

No activity on the line.

On, flashing

Activity present on the line (in

reception and/or transmission.

—
Table 5.20 Indication / Ekip Com Profinet -module

—
Fig. 5.23 Signals of Ekip Com Profinet -module

The following table illustrates the ports
used by the module:

Ethertype

Port

Service

Notes

0x88CC

LLDP

Link Layer Discovery Protocol

0x8892 (Profinet)

Profinet IO

Specific for real time

communications (RT)

0x0800

34964/udp

Profinet-cm

(Context Manager)

DCE/RP

—
Table 5.19 Ports of Ekip Com Profinet –module

CD
, T

Summary of Contents for Zenith ZTG 30





















































































































Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands

ABB Zenith ZTG 30, Operation, Maintenance And Installation Manual

Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands