ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 109

Page: 109 / 116

109

—

10. Accessories

Warning

Any troubleshooting should be conducted by

trained and authorized personnel only.

Appropriate personal protectiveequipment

(PPE) shall be used when troubleshooting the

ATS panel.

Hazardous voltage may be present. Discon-

nect all power sources before performing

work inside the ATS panel.

Failure to do so may result in serious injury

or death.

—

10.1 Phase barriers

Phase barriers must be used to maintain a
clearance of 1 inch on the automatic
transfer switch types. Where required,
they are included with the shipment of
ZTG series ATS Panel.

—
Fig. 10.1 Mounting of phase barriers, type OXEB_

A07

OXEB_

More information, see animation:
Installation of accessories - TruONE® ATS
(https://youtu.be/qV2KoIv38GY).

Summary of Contents for Zenith ZTG 30





















































































































Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands

ABB Zenith ZTG 30, Operation, Maintenance And Installation Manual

Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands