ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 48

Page: 48 / 116

Ze nit h Z TG S e r i e s AT S ,

O PER AT I O N , M A I N T EN A N C E , A N D I N S TA L L AT I O N G U I D E

Settings

*Default

Standard I/O Settings

I 01 / I 02 / I 03

Function

No function

Input disabled.

Emergency Stop*

(default in I 01)

Transfers to O position in delayed transition I-O-II
type switches. Disables automatic control mode in
both delayed and open transition types.

Remote Test On Load*

(default in I 02)

Start/stop test on load sequence in rising (NO) or
falling (NC) edge of the input signal.

Remote Test Off Load*

(default in I 03)

Start/stop test off load sequence in rising (NO) or
falling (NC) edge of the input signal.

Inhibit AUTO Mode

Prevent switch control operations, configuration,
test sequences and generator start in case of
priority source failure.

Manual Retransfer

Disables automatic transfer back to priority source.

Source Priority S1

Sets priority for source 1 in transformer-transformer

application.

Source Priority S2

Sets priority for source 2 in transformer-transformer

application.

Inhibit Transfer

Disables automatic transfer from priority source to
non-priority source.

Bypass Running Time
Delays

Bypass any currently running time delay

Remote Control to S1

Transfer to S1 when active. Overridden by activated

'Remote Control to OFF' signal.

Remote Control to OFF Transfer to O position when active.

Remote Control to S2

Transfer to S2 when active. Overridden by activated
'Remote Control to OFF' or 'Remote Control to S1'

signals.

Reset Alarm

Reset any active switch control alarms (open I
failure, close I failure, open II failure, close II failure)

Manual-Auto Mode

Toggle automatic/HMI control mode, input is active
only in rising/falling edge according to contact type.

Contact
type

Active open.

NO*

Active closed.

O 01

Function

No Function

Output disabled.

Alarm / Product
availability*

Signals any active alarms or ATS being disabled for
automatic transfer operations.

Load Connected to S1

Switch in position I.

Load Disconnected

Switch in position O.

Load Connected to S2

Switch in position II.

Continued on the next page

Summary of Contents for Zenith ZTG 30





















































































































Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands

ABB Zenith ZTG 30, Operation, Maintenance And Installation Manual

Search results

Summary of Contents for Zenith ZTG 30

Reviews:

Related manuals for Zenith ZTG 30

Brands by name

Popular brands