ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 100 | Manualshive

Page: 100 / 116

background image

2

100

Ze nit h Z TG S e r i e s AT S ,

O PER AT I O N , M A I N T EN A N C E , A N D I N S TA L L AT I O N G U I D E

—

9.1 Basic Tools for Installation and Maintenance

Tool

Task

1/4" to 1/2" Allen head socket driver

Power cable connection

Torque wrench

Torqueing of the lugs and other hardware as required.

Range of device to be 50 - 500 in-lbs (5-57 N-m)

Torque screwdriver

Torqueing of control wire terminations, auxiliary contact

input terminals. 5 - 25 in-lbs (0.5 - 2.8 N-m)

Wire cutters/wire crimpers

Auxiliary contacts wire installation, Options installation

Voltmeter

Trouble shooting tool for measuring incoming voltage,
frequency, continuity and control signal transmission.

Controller default password 00001

Changing parameters within the controller

—
Table 9.1 Required tools for common installation and maintenace tasks

—

9.2 Equipment Inspection and Storage

Warning

When performing a hi-pot or dielectric test on

the power section of the ATS panel, DISCON-

NECT the complete electronics, controller,

and mechanism section of the ATS from the

power section to avoid potential damage to

the electronics.

Once you have received the transfer
switch, inspect it for any damage. This in-
cludes damage to the enclosure, power
panel, control panel and wiring harness. If
any damage is found or suspected, file a
claim as soon as possible with the carrier
and notify the nearest ABB Zenith
representative.

Before installation, if it is necessary, store
the transfer switch in a clean dry place,
protected from dirt and water. Provide
ample air circulation and heat, if neces-
sary, to prevent condensation.

See table 7.1 for recommended storage
and ambient operating temperatures.

«
...
98
99
100
101
102
...
»

Summary of Contents for Zenith ZTG 30





















































































































Reviews:

No comments

Related manuals for Zenith ZTG 30

Brand: C&H Technologies Pages: 1

Brand: D-Box Pages: 31

SUPERSTACK 3 3226

Brand: 3Com Pages: 5

Brand: 3Com Pages: 139

CoreBuilder 7000

Brand: 3Com Pages: 150

CoreBuilder 7000

Brand: 3Com Pages: 264

Brand: 3Com Pages: 574

Brand: 3Com Pages: 333

SUPERSTACK 3 3226

Brand: 3Com Pages: 70

OfficeConnect 3C16790C

Brand: 3Com Pages: 18

Brand: 3Com Pages: 1314

SuperStack II Switch 1100

Brand: 3Com Pages: 62

Brand: RDL Pages: 4

Allen-Bradley 194U Series

Brand: Rockwell Automation Pages: 2

Brand: Steren Pages: 13

Brand: Gira Pages: 2

Brand: Jabra Pages: 13

Tek-CARE NC554/8

Brand: TekTone Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands