ABB Zenith ZTG 30 Operation, Maintenance And Installation Manual Download Page 79 | Manualshive

Page: 79 / 116

background image

79

1

—
Fig. 5.24 Ekip Com EtherNet/IP -module

5.6.6 Ekip Com EtherNet/IP -module

The Ekip Com EtherNet/IP is an accessory
module that can act as a communication
module integrating the automatic trans-
fer switch in an industrial remote supervi-
sion and control network. The module is
suitable for all ZTG(D) 30-1200 A, 200-480
Vac automatic transfer switches.

It can be connected to an Ethernet net-
work with a EtherNet/IP™ -communica-
tion protocol, and allows you to:

• Connect the automatic transfer switch

to the network, with dialog
functionality.

• Provide the status information of the

automatic transfer switch (e.g. open,
closed).

For the communication bus, a cable of
type Cat.6 S/FTP must be used (Cat.6
with S/FTP double shielding).

The following table illustrates the ports
used by the module:

Port

Protocol

Notes

44818

TCP

Encapsulation Protocol

(example: ListIdentity, UCMM,

CIP Transport Class 3)

44818

UDP

Encapsulation Protocol

(example: ListIdentity)

2222

UDP

CIP Transport Class 0 or 1

—
Table 5.22 Ports of Ekip Com EtherNet/IP -module

Notice

Since this module allows the access to the

data contained in the automatic transfer

switch, it can only be connected to networks

possessing all the necessary requirements for

security and prevention of unauthorized ac-

cess (for example, the network of the control

system of an installation). It is responsibility

of the installer to make sure that all the neces-

sary security measures are adopted (for ex-

ample firewalls and so on). The module cannot

be connected directly to the Internet. It is rec-

ommended to connect it only to dedicated

Ethernet networks using the EtherNet/IP™

-communication protocol.

L

CD
, T

O

U

CH

«
...
77
78
79
80
81
...
»

Summary of Contents for Zenith ZTG 30





















































































































Reviews:

No comments

Related manuals for Zenith ZTG 30

Brand: D-Link Pages: 267

Brand: H3C Pages: 1089

Brand: D-Link Pages: 17

Brand: Black Box Pages: 4

Brand: CYP Pages: 32

Brand: TRENDnet Pages: 12

Brand: Ask Pages: 4

Brand: Vega Pages: 44

SET-2000 Oil/Sludge

Brand: Labkotec Pages: 15

Brand: UNICOM Pages: 15

Brand: Alloy Pages: 33

Brand: Advantech Pages: 101

Brand: Origin Instruments Pages: 6

Tek-CARE NC554/8

Brand: TekTone Pages: 2

ControlCenter-IP-XS

Brand: G&D Pages: 56

S5130-EI Series

Brand: H3C Pages: 32

Brand: YOKOGAWA Pages: 74

Brand: IOGear Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands