background image

1SDH002031A1002    ECN000092998    Rev. B 

SACE Tmax XT2 

– XT4 | 41 

G Protection [2] 

 

Ekip M Touch 

G protection of the Ekip M Touch differs with the other models in the following ways: 

 

BlockOnStartUp

 block enabled and cannot be changed (see page 78) 

 

StartUp Time

 cannot be changed and set with the value of Motor StartUp (depending on 

the trip class, see page 66) 

 

Curve set as t = k not changeable 

 

Constraints, limitations, and additional functions 

 

With curve t = k/I

2

 the trip time is forced to t4 if the calculations result in a theoretical value 

that is lower than t4 itself 

 

With CB size 100A, without 

Vaux

 and with threshold I4 < 25 A, the threshold itself is forced 

to 25 A and the display shows the error 

Configuration

 

 

without 

Vaux

 and with time t4 < 100 ms, the time itself is forced to 100 ms and the display 

shows the error 

Configuration

 

 

depending on the set threshold I4, the protection is deactivated for Ig greater than:  
8 In with threshold I4 

 0.8 In;    6 In with 0.8 In > I4 

 0.5 In; 4 In 0.5 > In 

 0.2 In; 2 In with 

I4 >0.2 In 

 

From the service connector (with Ekip Connect) or with system bus communication it is also 
possible to access the block functions and the selectivity type, see page70. 

 
 

MCR Protection 

 

 

Function 

The protection is active for a calculated period of time starting from the change of state open 

 

closed, then it turns off. 
If during this period the current of one or more phases exceeds the I3 threshold, after a fixed time 
that cannot be programmed the protection sends the TRIP command. 

 

To verify and simulate the trip times based on all the parameters, see: 

 

Protection summary table with the operating characteristics (page 78) 

 

Chart with tripping curve (page 85) 

 

 

NOTE: to activate MCR, the I protection must be disabled 

 

Parameters 

 

Parameter 

Description

 

Default 

Enable 

Enables/disables  protection  and  availability  on  menu  of  the 
parameters 

OFF 

Threshold I3 

Defines the value that activates the protection. 

 

The value is expressed both as an absolute value (Ampere) and as 
a relative value (In), settable in a range: 
1.5 In .. 15In with 0.1 In step 

6 In 

Monitor time 

Defines the interval of time in which the MCR protection is active, 
calculated from the open 

 closed status change 

 

The value is expressed in seconds, which are settable in a range: 
0.04 s .. 0.5 s with 0.01 s step 

0.04 s 

 
Constraints, limitations, and additional functions 

 

From the service connector (with Ekip Connect) or with system bus communication it is also 
possible to access the block functions and the selectivity type, see page70. 

 
 

 
 

 

Summary of Contents for SACE Tmax XT2
















































































































































































































Reviews: