1SDH002031A1002 ECN000092998 Rev. B
SACE Tmax XT2
– XT4 | 202
Remote
configurations
From the service connector (via Ekip Connect) or with system bus communication it is also
possible to access additional parameters.
Parameter
Description
Default
CRL Enable
Use the CRL (Certificate Revocation List) to verify the validity of the
server certificate
Clock update
hardening enable
Enables monitoring of the time transmitted by SNTP servers
SNTP Server
Location
Sets the location of the SNTP server relative to the network where
the module is installed
SNTP Time zone
Defines the time zone to be used for synchronization
+00:00
SNTP Daylight
Saving Time
Specifies whether the local country uses daylight saving time (ON)
or not (OFF)
OFF
Disable Gratuitous
ARP
Enable (ARP Enabled) the periodic generation of a Gratuitous ARP
message, used by Ekip Connect to quickly find the modules with an
Ethernet scan without knowing the IP address in advance
ARP
enabled
Remote
information
From the service connector (via Ekip Connect) or with system bus communication it is also
possible to access additional information.
Information
Description
HW and Boot version
General module information
Flash CRC status and result
Information on the correctness of the SW on the module
Publish enable configuration
Enable content in the Security File
Configuration file
Name of the file with the information to be transmitted
(measurements, etc.)
Security file
Name of the file with the information requested by the module to
perform the transmission (addresses, certificates, etc.)
Certify Revocation List
Name of the file containing the list of revoked certificates
Executable file
Name of the firmware update executable file
Configuration error
Error status of the module configuration
Sample time
Period of time for sampling data from connected devices
Log time
Period during which the acquired data are saved in the log
Upload time
Period (calculated by the module) between each data transmission
Configured device
Number of modules involved in the network with the Hub module
Polling period API events
Period for which the module communicates with the API device
Connection client 1, 2, 3
Addresses of the Modbus TCP clients connected to the module
Statistics
Log of the last save operations and percentage of resources in use
Status plant side
Information related to the quality of communication with other devices
Status Cloud side
Status of errors related to the TLS session established between the
module and the server
Application status
Progress indicators for operations
Status
General module indicators: status of SNTP, flash, cable connection,
FW availability, file errors, etc
Summary of Contents for SACE Tmax XT2
