manualshive.com logo in svg

ABB SACE Tmax XT2, User Manual

Share
Download
ABB SACE Tmax XT2 User Manual Download Page 4

1SDH002031A1002    ECN000092998    Rev. B 

SACE Tmax XT2 

– XT4 | 4 

Introduction 

1 -  Content 

 

Overview

  This manual  illustrates  the  characteristics  of  the  Ekip Touch Trip units  mounted  on  CB  SACE 

Tmax XT2 - XT4, including:  

1.  Overview 
2.  Management operations: installation, maintenance, malfunction identification 
3.  Operating conditions 
4.  Reference guide for changing parameters and measurement display 
5.  Accessories 

 
 

Recipients 

In accordance with IEC 60050, this manual refers to two user profiles: 

 

Skilled person  in  the electrical field (IEV 195-04-01):  person  with relevant education and 
experience to enable him or her to perceive risks and to avoid hazards which electricity can 
create 

 

Instructed  person  in  the  electrical  field  (IEV  195-04-02):  person  adequately  advised  or 
supervised by electrically skilled persons to enable him or her to perceive risks and to avoid 
hazards which electricity can create 

 

 

IMPORTANT: This manual details the operations that can be performed by people 
trained in the electrical field. 
All  the  remaining  operations  described  in  the  manual  must  be  carried  out  by 
experts in the electrical field.  
ABB will not be held responsible for damage to property or persons due to non-
compliance with the instructions contained in this document. 

 
 

 

Requirements 

and supporting 

documentation  

For an optimal installation and configuration of Ekip Touch, read the information contained in this 
manual and in the technical product documentation available on the 

ABB library

 website: 

 

Document 

Code 

Description 

Technical catalog 

1SDC210100D0201 

General catalog CB SACE Tmax XT 

Wiring diagrams 

1SDM000068R0001 

Wiring diagrams CB SACE Tmax XT2-
XT4 

Installation 
Instructions 

1SDH000721R0001 

 

1SDH0000721R0002 

Installation instructions CB SACE Tmax 
XT2-XT4 

 
 

Production notes 

The information contained in this document was written in Italian and then translated into other 
languages to meet the legislative and/or commercial needs of the product in question. 
 
 

 

 

 

Summary of Contents for SACE Tmax XT2
















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands