manualshive.com logo in svg

ABB ProcessMaster FEM611, Operating Instruction

Share
Download
ABB ProcessMaster FEM611 Operating Instruction Download Page 67

67

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

8      . . .Diagnosis / error messages

 . . .Overview

Error no . / Range

Error text

Current output

Digital output

Pulse output

LCD display

Error maskable?

C078.004 / Config.

Flowrate to zero.
Check digital in 
terminals.

4 mA (0 % flow)

Current value - no 

change.

0 Hz

0 %

Menu "...Group 

Masking".

C076.006 / Config.

All totalizer stopp.
Check digital in 
terminals.

Current value - no 

change.

Current value - no 

change.

Current value - no 

change.

Current value - 

no change.

C074.007 / Config.

Totalizer reset.
Reset of one or more 
Totalizers.

Current value - no 

change.

Current value - no 

change.

Current value - no 

change.

Current value - 

no change.

Menu "...Group 

Masking".

C072.003 / Config.

Simulation is on 
Simulated values.
Switch off Simulation 
Mode.

Current value - no 

change.

Current value - no 

change.

Current value - no 

change.

Current value - 

no change.

C070.027 / Config.

An alarm is  
simulated.
Switch off alarm 
simulation.

Current value - no 

change.

Current value - no 

change.

Current value - no 

change.

Current value - 

no change.

S065.044 / Operation

Inhouse temp. alarm.
Reduce ambient 
temperature.

Current value - no 

change.

No response

No response

Current value - 

no change.

S064.041 / Operation

EPD alarm.
Secure pipe is 
completely filled.

Alarm - as configured in 

menu "Curr. at EPD 

Alarm".

Alarm if DO is 

configured as "Logic / 

Alarm Signal / EPD".

0

0 %

Menu "...Group 

Masking".

S062.039 / Operation

Sensor temp. limits 
alarm. Change limits 
or change fluid 
temperature.

Current value - no 

change.

No response

Current value - no 

change.

Current value - 

no change.

Menu "...Group 

Masking".

S052.017 / Operation

Curr.Out 31 / 32 is 

saturated. CO 
process value out of 
range. Adapt Qmax.

Alarm - as configured in 

menu "Curr.Out > 

20.5mA".

Current value - no 

change.

Current value - no 

change.

Current value - 

no change.

Menu "...Group 

Masking".

S047.016 / Operation

Pulse output is cut 
off. Wrong config. 
Check pulse out 
configuration.

Current value - no 

change.

Current value - no 

change.

Maximum possible 

pulse rate

Current value - 

no change.

Menu "...Group 

Masking".

S046.001 / Operation

Mass flowrate 
exceeds limits. Check 
flowrate and alarm 
limits.

Current value - no 

change.

Alarm if DO is 

configured as "Qm 

Massflow Max" or "Qm 

Massflow Min".

Current value - no 

change.

Current value - 

no change.

Menu "...Group 

Masking".

S044.002 / Operation

Volume flowrate 

exceeds limits. Check 
flowrate and alarm 
limits.

Current value - no 

change.

Alarm if DO is 

configured as "Qv 

Volumeflow Max" or "Qv 

Volumeflow Min".

Current value - no 

change.

Current value - 

no change.

Menu "...Group 

Masking".

S041.034 / 

Electronics

DC feedback  
regulation. Check 
conditions of 
application. Call 
service.

4 mA (0 % flow)

No response.

0 Hz

0 %

Menu "...Group 

Masking".

S040.031 / 

Electronics

Coil impedance 
alarm. Call service.

Current value - no 

change.

No response.

Current value - no 

change.

Current value - 

no change.

Menu "...Group 

Masking".

Summary of Contents for ProcessMaster FEM611





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands