manualshive.com logo in svg

ABB ProcessMaster FEM611, Operating Instruction

Share
Download
ABB ProcessMaster FEM611 Operating Instruction Download Page 65

65

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

8      . . .Diagnosis / error messages

 . . .Error messages

Operation outside of specifications (Out Of Spec .)

Error no . / Range

Text on the LCD display

Cause

Remedy

S065.044 / Operation

Inhouse temp. alarm. Reduce 
ambient temperature.

Fluid or ambient temperature is out of spec.

Check proces conditions reduce temperature.

S064.041 / Operation

EPD alarm. Secure pipe is 
completely filled.

Sensor not filled.

Check for empty pipe Make sure sensor is 
filled completely.

S062.039 / Operation

Sensor temp. limits alarm. 
Change limits or change fluid 
temperature. 

The fluid temperature is out of Limits.

Check process condition and adjust alarm 
limits.

S052.017 / Operation

Curr.Out 31 / 32 is saturated. CO 

process value out of range. Adapt 
Qmax.

The selected current output 31 / 32 process 

value is out of measuring range.

Adapt measuring range.

S047.016 / Operation

Pulse output is cut off. Wrong 
config. Check pulse out 
configuration.

The caluclated output pulse or frequency is 
above the configurated limit frequency.

Check pulse out configuration.

S046.001 / Operation

Mass flowrate exceeds limits. 
Check flowrate and alarm limits.

The mass flow is below or above the 
configured limit values "Qm Massflow Min" 
and "Qm Massflow Max".

Check the parameter settings in the "Process 
Alarm / ...Alarm Limits" menu and adjust if 
necessary. Check mass flow.

S044.002 / Operation

Volume flowrate exceeds limits. 

Check flowrate and alarm limits.

The volume flow is below or above the 

configured limit values "Qv Volumeflow Min" 
and "Qv Volumeflow Max".

Check the parameter settings in the "Process 
Alarm / ...Alarm Limits" menu and adjust if 
necessary. Check volume flow rate.

S041.034 / Electronics

DC feedback  regulation. Check 
conditions of application. Call 
service.

Multi-phase measuring media that produce a 
very high level of noise. Stones or solids that 
produce a very high level of noise.
Galvanic voltages at the measuring 
electrodes.
Conductivity of measuring medium is not 
evenly distributed (e.g., directly after 
injection points).

Contact ABB Service.

S040.031 / Electronics

Coil impedance alarm. Call 
service.

Coil Inductance changed, coil damaged, coil 
isolation damaged, outer magnetic fields.

Contact ABB Service.

Error no . / Range

Text on the LCD display

Cause

Remedy

M038.010 / Electronics

Sensor memory defective.
Mem. or connect. defective. 
Replace memory.

Defective NV-Memory module. NV-Memory 

module is not plugged in.

Check if NV-Memory module is plugged in. 

Call Service.

M037.015 / Electronics

NV chips defect on Motherboard.

Defective MB. Replace MB. Call 
Service.

Defective NV-Memory.

Exchange Motherboard. Call Service.

M032.023 / Config.

Curr.Out 31 / 32 not calibrated.

Call Service.

The Current Output 31 / 32 is not calibrated.

Call Service.

M028.008 / Config.

Display value is < 1600 h at 

Qmax.
Change mass Unit or vol. Unit for 
Totalizer.

Totalizer unit is too small. 

Change the mass or volume totalizer unit.

M026.005 / Config.

Maintenance interval is reached.
Perform maintenance.

Set "Preset Maint. cycle" to zero to deactivate 
the maintenance timer.

Perform maintenance work. Start new cycle.

M024.009 / Config.

Device not  calibrated.
Call Service.

The device is not calibrated.

Call Service.

Maintenance

Summary of Contents for ProcessMaster FEM611





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands