manualshive.com logo in svg

ABB ProcessMaster FEM611, Operating Instruction

Share
Download
ABB ProcessMaster FEM611 Operating Instruction Download Page 51

51

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

Menu / parameter
Device Setup /  . . .Sensor /  . . .Operating Mode

Flow Direction

Sets the measuring direction for the sensor.
As delivered, the device measures and counts in both flow directions.
•  Forward & Reverse: The device measures in both flow directions.
•  Forward only: The device measures only in the forward flow direction.
•  Reverse only: The device measures only in the reverse flow direction.
Default setting: Forward & Reverse

Flow Indication

Inverts the flow direction displayed.
Default setting: Normal

7      . . .Operation

 . . .Parameter descriptions

Device Setup /  . . .Transmitter

 . . .Units

Selection of submenu ‘...

Units

’ using   .

Damping

Select the damping.

The value (0.02 ... 60 s) set here relates to 1 Τ (Tau). The value refers to the response time for a step flowrate 

change. It affects the instantaneous value in the display and at the current output.

Default setting: 1 second

Damping On/Off

Switches the damping on or off.

Density Fixed Value

If the flow is measured and indicated in mass flow units, a fixed density must be taken into account for the 

calculations. To convert the flow rate to mass flow units, a density value from 0.01 ... 5.0 g/cm3 can be entered.

 . . .Cut Off

Selection of submenu ‘...

Cut Off

’ using   .

TX Location TAG

Entry of the measuring point tag for the transmitter. 

Alphanumeric, max. 20 characters

TX TAG

Enter the tag number for the transmitter.

Alphanumeric, max. 20 characters

Plant Data Sync.

Tx -> Sens
The settings are redundantly saved in two data modules. One of them is the SensorMemory, the other is the 
transmitter motherboard (backplane). 
By selecting ‘Tx -> Sens’, location-specific settings such as measuring range or damping are replicated from 
the transmitter motherboard (backplane) to the SensorMemory.
Sens -> Tx
By selecting ‘Sens -> Tx’, location-specific settings such as measuring range or damping are replicated from 
the SensorMemory to the transmitter motherboard (backplane).

Device Reset

For service purposes only. Restarts the device without the need for cycling the power.

Restore Factory Def.

All user-accessible parameters will be reset to the factory default settings.

 . . .Feature Settings

Selection of submenu ‘...

Feature Settings

’ using   .

 . . .System Zero

Selection of submenu ‘...

System Zero

’ using   .

Noise Reduction

Activates the filter technology for noise reduction.

Filter: Off, Filter 15, 30, 60 (15: lower filtering, 60: strong filtering)
Filter setting affects 20 mA signal (damping).

Default setting: Off

Menu: Device setup

Summary of Contents for ProcessMaster FEM611





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands