manualshive.com logo in svg

ABB ProcessMaster FEM611, Operating Instruction

Share
Download
ABB ProcessMaster FEM611 Operating Instruction Download Page 54

54

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

Menu / parameter

Description

Input/Output

...Curr.Out 31/32

Selection of submenu ‘...Curr.Out 31/32’ using 

.

...Dig.Out 41/42

Selection of submenu ‘...Dig.Out 41/42’ using 

.

...Dig.Out 51/52

Selection of submenu ‘...Dig.Out 51/52’ using 

.

7      . . .Operation

 . . .Parameter descriptions

Menu: Input/output

Input/Output / ...Curr.Out 31/32

Output Value

Selection of process variable issued at the current output.
• 

Qm [%]: mass flow

• 

Qv [%]: volume flow

Curr.Out Mode

•  Selection of operating mode for the current output.
•  ‘4-20mA FWD’ Flow output in forward flow direction: 

4 mA = no flow  
20 mA = maximum flow

•  ‘4-12-20 mA’: Flow output in forward and reverse flow direction: 

4 mA = maximum flow in reverse flow  
12 mA = no flow 
20 mA = maximum flow in forward flow

• 

‘4-20mA FWD/REV’: Flow output in forward and reverse flow direction without distinguishing between 

flow directions: 
4 mA = no flow  
20 mA = maximum flow

Default setting: 4-20mA FWD/REV.

Curr.Out at Alarm

Selection of status of the current output in error condition.
The output ‘low alarm' or ‘highalarm’ current is set in the subsequent menu.
Default setting: High Alarm.

Low Alarm

Sets the current for Low Alarm (3.5...3.6mA).
Default setting: 3.5 mA

High Alarm

Sets the current for High Alarm (21...22.6mA).
Default setting: 21.8 mA

Curr.Out > 20.5mA

Behavior of the current output if 20.5 mA is exceeded.

• 

Hold Last Value: The last measured value is retained and issued.

•  High Alarm: The high alarm current is issued.
•  Low Alarm: The low alarm current is issued.

Default setting: Hold Last Value

Curr.Out < 3.8mA

Behavior of the current output if 3.8 mA is not reached.

• 

Hold Last Value: The last measured value is retained and issued.

•  High Alarm: The high alarm current is issued.
•  Low Alarm: The low alarm current is issued.
Default setting: Low Alarm

Curr. at EPD Alarm

Behavior of the current output during empty meter tube conditions.
•  Off: No effect on current output.
• 

Q=0%: Current output is set to 4mA which is "no flow".

• 

Hold Last Value: The last measured value is retained and issued.

•  High Alarm: The high alarm current is issued.
•  Low Alarm: The low alarm current is issued.
Default setting: Off

Summary of Contents for ProcessMaster FEM611





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands