manualshive.com logo in svg

ABB ProcessMaster FEM611, Operating Instruction

Share
Download
ABB ProcessMaster FEM611 Operating Instruction Download Page 37

37

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

7      . . .Operation

Process display

Switching to the information level 

(Operator menu)

On the information level, the operator menu can be used to 
display diagnostic information and choose which operator 
pages to display.

Measuring point tagging

Current process values 

‘Button function’ symbol

‘Parameterization protected’ symbol

1
2
3
4

The process display appears on the LCD display when the 
device is switched on. It shows information about the device 
and current process values.
The way in which the current process values are shown can be 
adjusted on the configuration level.
The symbols at the bottom of the process display are used to 
indicate the functions of the operating buttons 

  and 

  , 

in addition to other information.

1 

Open the Operator Menu using 

.

2 

Select the desired submenu using  

/

  .

3 

Confirm the selection with  

.

Process display

Operator Menu

Diagnostics

Operator Page 1
Operator Page 2

Back

Select

Menu

Description

… / Operator Menu

Diagnostics

Selection of sub-menu "Diagnostics"; see also 
chapter "Error messages on the LCD display" on 

page 38.

Operator Page 1... n

Selection of operator page to be displayed.

Autoscroll

When Autoscroll is activated, automatic 
switching of the operator pages is initiated on 
the process screen.

Signals View

Selection of submenu "Signals View" (only for 

service purposes).

Symbol

Description

      /

Call up information level.
When Autoscroll mode is activated, the    icon 
appears here and the operator pages are 
automatically displayed one after the other

Call up configuration level.
The device is protected against changes in the 
parametrization.

 

Figure 44  Process display (example)

Summary of Contents for ProcessMaster FEM611





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands