manualshive.com logo in svg

ABB ProcessMaster FEM611, Operating Instruction

Share
Download
ABB ProcessMaster FEM611 Operating Instruction Download Page 64

64

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

8      . . .Diagnosis / error messages

 . . .Error messages

Error no . / Range

Text on the LCD display

Cause

Remedy

F086.019 / Electronics

Curr.Out 31 / 32 com error. 

Defective Board. EMC 
disturbance. Call Service.

Defective Motherboard Hardware. EMC 
disturbance.

Call Service.

F084.011 / Electronics

NV data defect. Data storage 

irreparable. Call Service.

Data in SensorMemory corrupt.

Call Service.

F082.014 / Electronics

Incompatible Frontend Board. 
Frontend not fit to Motherboard. 
Call Service.

Wrong Frontend or Mother Board.

Call Service.

F081.026 / Electronics

MB voltages outside range. 
Defective Motherboard HW. Call 
Service.

Defective Mother Board Hardware.

Replace Mother Board.
Call Service.

Error no . / Range

Text on the LCD display

Cause

Remedy

C078.004 / Config.

Flowrate to zero.
Check digital in terminals.

The option card Digital Input is configured to 
"set flowrate to zero" and this event is 
triggered.

Check Digital Input terminals and 
configuration.

C076.006 / Config.

All totalizer stopp.
Check digital in terminals.

The option card Digital Input is configured to 
"All Totalizer stopp" and this event is 
triggered.

Check Digital Input terminals and 
configuration.

C074.007 / Config.

Totalizer reset.
Reset of one or more Totalizers.

The option card Digital Input  is configured 
to "ResetTotalizer" and this event is 
triggered.

Check Digital Input terminals and 
configuration.

C072.003 / Config.

Simulation is on Simulated 
values.
Switch off Simulation Mode.

The simulation of a process value or an 
output is active.

Switch off simulation mode.

C070.027 / Config.

An alarm is  simulated.
Switch off alarm simulation.

The simulation of an alarm is active.

Switch alarm simulation to "Off".

Function check

Summary of Contents for ProcessMaster FEM611





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands