manualshive.com logo in svg

ABB ProcessMaster FEM611, Operating Instruction, Page: 21 / 84

Share
Download
ABB ProcessMaster FEM611 Operating Instruction Download Page 21

21

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

5      . . .Installation

Electrical connection

G12018

+

-

+

3

M1

2S E2 E1 1S

3

B

B

164 ft (50 m)

31 32

A

41 42 51

52

1+ 2-

PE

+

-

PE

PE

PE

PE

L

N

FE

FE

M2

M1

2S E2 E1 1S

M2

Connections for power supply and outputs

Connections for signal cable (remote mount design only)

A
B

Figure 30  Electrical connections

Note

For detailed information about earthing the transmitter and 
the sensor, please refer to chapter "Grounding the flowmeter 
sensor" on page 15.

Connections for the power supply

Connections for the signal cable

Only for remote mount design.

Connections for outputs

AC power supply
Terminal

Function / comments

L

Phase

N

Neutral conductor

PE / 

Protective earth (PE)

DC power supply
Terminal

Function / comments

1+

+

2-

-

PE / 

Protective earth (PE)

Terminal

Function / comments

31 / 32

Active current output

The current output is "active" mode. The source to 

drive the 20 mA loop is in-built in the transmitter.

41 / 42

Passive digital output DO1

The output can be configured as a pulse output, 
frequency output or switch output on site.

51 / 52

Passive digital output DO2

The output can be configured as a pulse output, 
frequency output or switch output on site.

Functional earth 

Terminal

Function / comments

Color

FE

Not connected

-

3

Measurement potential

green

2S

Signal line

-

E2

Signal line

blue

E1

Signal line

violet

1S

Shield for E1

-

M1

Magnet coil

brown

M2

Magnet coil

red

Shield

-

-

Not connected

orange/yellow

Summary of Contents for ProcessMaster FEM611





















































































Reviews:

No comments