ABB AKD-10 Installation And Maintenance Manual Download

Page: 57 / 77

Figure 56

Figure 57

AKD-10, Door Interlocking Components for WPS-08/ WPH-08/WPX-08/WPS-16/WPH-16/WPS-20 Breaker

AKD-10, Door Interlocking Components for WPS-32/WPH-32/WPX-32/WPS-40/
WPX-40/WPS-50/ WPX-50 Breaker.

Install AKD-10 & Substructure type 3200, 4000 & 5000 Retrofill Breaker

lt must be ensured that the supply power to the
Shack and Saad compartment is turned off/
compartment is denergized for all the incoming
and outgoing circuits of the LVS prior to any work
being conducted on it.

During the installation and related work on the
equipment, it must be ensured that the operator
is using the prescribed PPE for the specified
tasks

Ensure only qualified personnel install, operate, service, and maintain all electrical

equipment

Danger

Door Interlock System

During the installation and related work on the
equipment, it must be ensured that the operator
is using the prescribed PPE for the specified
tasks

Ensure only qualified personnel install, operate, service, and maintain all electrical

equipment

Danger

Details regarding installation of door interlock system are shown in Figure 56 & 57.

Summary of Contents for AKD-10














































































Search results

Summary of Contents for AKD-10

Reviews:

Related manuals for AKD-10

Brands by name

Popular brands

ABB AKD-10, Installation And Maintenance Manual

Search results

Summary of Contents for AKD-10

Reviews:

Related manuals for AKD-10

Brands by name

Popular brands